例句與造句

1. Test methods of pull strength for printed boards
   印制板拉脫強度測試方法
2. Standard test methods for measuring pull strength of microelectronic wire bonds
   微電子器件金屬絲連接抗拉強度測量的標準試驗方法
3. Hole pull strength
   孔壁抗拉強度
4. Test method for physical - chemical properties of electrical carbon product . pull strength of brush connection
   電炭制品物理化學性能試驗方法.電刷軟接線的脫出拉力
5. Each lot of product will be tested and re - tested on the inspection equipment . no delivery shall be made until after all the pulling strength , pressure , torque are comforming to the specification of the customers
   第一批量，均再經嚴密的檢驗設備再測量，嚴格檢驗確定完全符合圖面的規格要求才能出貨。
6. It's difficult to find pull strength in a sentence. 用pull strength造句挺難的
7. The 3 batches with 7 groups of prism concrete test specimens and the 3 batches with 22 groups of cube ones were used in mechanical properties test , and a series of parameters of rpc was acquired such as prismatic strength , the cubic strength , split and pull strength , deformation module , peak strain , poisson ' s ratio
   進行三批7組棱柱體試件和三批22組立方體試件的力學性能試驗，測定了rpc200棱柱體抗壓強度、立方體強度、劈拉強度、彈性模量、峰值應變、泊松比等參數，并建立了變形模量和峰值應變的擬合公式。
8. At this elastic pulling status which guarantees the balance of the pulling strength on both sides , the waist is relaxed with muscle fibre , aponeurosis , joint capsule refreshed and the disorder of lumbar posterior joint and shift of lumbar intervertebral nucleus pulposus can be corrected , thus reaching the object of health care and therapy
   在彈性牽引狀態下能活動腰部，還能保證左右牽引力平衡，理順肌纖維、筋膜、小關節囊，糾正腰椎后關節紊亂和腰椎間盤髓核的移位，從而達到保健和治療的目的。
9. Have to out : 1 temperature constructional reinforcing not can place in heat area to mass concrete design . temperature constructional reinforcing of bottom of mass concrete need content that owing to temperature change produce bottom control stress smaller than anti - pull strength at the same . get minimum rate of reinforcing to content construct request
   得出： 1在大體積混凝土結構的溫度構造鋼筋配置中，構造鋼筋不宜放置于高溫區；大體積混凝土的底部溫度構造鋼筋應滿足溫度變化產生的底部約束拉應力小于混凝土同齡期的抗拉強度的要求，從而求出抗拉要求的最小配筋率。